Fingertec Ingressus IV User Manual

ControllersCentralization of Access Control Devices Made EasyInstaller Guide

103 • BEFORE INSTALLATION THE POWER SUPPLYIngressus must be powered up by 12VDC 3A independently. DO NOT share the power supply with any other devices

11Idle/fail verificationsSuccess verificationPower supply cut offNC Type (Fail safe)Ingressus outputs constant at 12VDC. NC type door lock sys

12i-Kadexk-Kadex i-Kadex CAUTIONS WHEN HANDLING DOOR LOCK SYSTEM INSTALLATION: 1. DO NOT power up Ingressus, door lock system, or

13R2cR2cThe maximum length of each Wiegand reader and Ingressus shall not ex-ceed 100 meters. RS485 ReaderThe terminal can support RS485 network to li

14 i-KadexINBEEPGLEDWD1WD0GND+12vBEEPGLEDWD1WD0GND+12vNote:1. Only supply 12VDC 3A to Ingressus. Recommended to use switching power supply w

1512C APower Supply485--485+Reader 1 Reader 2 Reader 3 Reader 4+12vGND485--485+485--485+485--485+485--485+Note:1. All Wiegand readers must provide

16LOCK 1 LOCK 2SENGNDNOCOMNCSENGNDNOCOMNC12345SENGNDNOCOMNCLOCK 1Door sensorOverride keyswitch (NC Type)CDEmergency break glass (NC Type)3212VDC Elect

171234512V3A Power SupplyGND +12VNote:1. DO NOT install with door lock systems connected to AC power.2. Each door lock system should be in

18INGNDSmokeDetectorNOCOMNCAlam/Siren--+PowerSupply+--RS232/485Converter485+485---SGNDRS485RS232CONNECTING TO AUX COMPONENTSCONNECTING TO PC VIA RS485

19CONFIGURATION OF DIP SWITCHThe configuration of DIP switch at Ingressus Only use switch 1 to 6 to setup Device ID of Ingressus. Each number repre-se

CONTENTS 1 • INTRODUCTION 3 The Overview of Hardware 5 The Overview of Installation & Communications 7 • Installations with door

20 Switch 1 2 3 4 5 6 Device ID Status of DIP switch 13 ON * ON ON * * 14 * ON ON ON * * 15 ON ON ON ON *

21 Switch 1 2 3 4 5 6 Device ID Status of DIP switch 58 * ON * ON ON ON 59 ON ON * ON ON ON 60 * * ON ON ON ON 61

22Name of LEDRS485 ReaderRS485 ServerWiegandRunPowerLANDescriptionsBlinks to indicate• RS485 reader captures and sends fingerprints or card ID

23Name of LEDLinkActRunDescriptionsLights up to indicate LAN (or TCP/IP) connection established. Blinks to indicate data transfer between Ingress

© 2014 Timetec Computing Sdn Bhd. All rights reserved. • 082014

3DIAGRAM ISlave Reader Credentials Sample Model Connection to IngressusRS 485 Fingerprint, card ID R2c RS 485 portWiegand Card ID, password i-

4Ingressus can support 2 types of door lock output, either wet contact or dry contact. For wet contact, Ingressus can output power to the door lock sy

5* These ports are available in Ingressus II.LED light indicatorsTCP/IP PortsDIP switchRS485 connection to PC/serverAUX output ports (max 2 ports)*Pow

6LED light indicatorsTCP/IP PortsDIP switchRS485 connection to PC/serverAUX output ports (max 4 ports)Power input to Ingressus (Max12V 3A)Door lock sy

7THE OVERVIEW OF INSTALLATION & COMMUNICATIONSThe installations with door lock system• Ingressus I• Ingressus II• Ingressus IVAux. Relay OutputAux

8WALLAluminium frameTo install Ingressus 1. Install an aluminium frame to a wall or an enclosure. 2. Hook the Ingressus to the aluminium frame. •

9MODELBASIC• Dimension (mm)• Power input (V)• Operating temperature (°C)• Operating humidity (%)• CPU• Flash memory (MB)• RAM (MB)• Polarity protectio